Oops. The compressor doesn't quite fit. 🤦‍♂️ | LOCKDOWN Day 51

Oops. The compressor doesn't quite fit. 🤦‍♂️ | LOCKDOWN Day 51


Clickable here
In today’s blog post, we will be discussing a YouTube video titled “Oops. The compressor doesn’t quite fit. 🤦‍♂️ | LOCKDOWN Day 51”. The video showcases the process of making drawer pulls out of solid lumber, with the speaker providing helpful tips and insights along the way. From setting the blade to a thirty-degree angle for precise cuts to sanding down the edges of the drawer pulls for a more comfortable grip, the video delves into the intricacies of creating these functional and visually appealing pieces. Additionally, the speaker shares their technique for positioning the drawer pulls towards the top of the drawer, making it easier to align them consistently on each drawer. Join us as we explore the details of this video and learn more about the art of woodworking.

Below Table of Contents

1. “Crafting Custom Drawer Pulls Using Solid Lumber: A Step-by-Step Guide”

In this step-by-step guide, we will show you how to craft custom drawer pulls using solid lumber. To begin, you can use any scrap piece of lumber, about an inch and a half wide. Set your blade to a thirty-degree angle and rip the wood at that angle. This will create the base for the drawer pull, which will be mounted onto the face of the drawer.

Next, it’s important to sand down the sharp edges of the base, so they’re not uncomfortable when grabbing the pull. Leave the two edges that will go against the door as they are. You can also sand down any other parts that you wish to smoothen. Repeat this process to create six drawer pulls in total before attaching them to the drawers.

Before attaching the pulls, make sure to sand everything smooth. Additionally, consider positioning the pulls at the top of the drawer rather than in the center. This makes it easier to align them consistently across all drawers. Draw tick marks in the center of each pull and drawer, and then line them up and glue them into place. No clamping is necessary, and the glue should set within a short time. To finish, push the pulls in until they are flush with the front of the cabinet. Finally, glue in some blocks in the back to secure the pulls. No clamping is required for this step either.

By following these steps, you can create your own custom drawer pulls using solid lumber. This adds a unique touch to your furniture while also ensuring a comfortable grip for easy handling. Experiment with different angles and shapes to achieve the desired look and feel. Stay tuned for more woodworking guides and tips!

2. “Achieving a Professional Look: Tips for Installing Drawer Pulls”

To achieve a professional look when installing drawer pulls, it is recommended to make the pulls out of solid lumber. Start by cutting the lumber at a thirty-degree angle to create a mounting piece that will attach to the face of the drawer. Sand down the edges of the piece that will be touched by fingers for a more comfortable grip. Repeat this process to create six pulls before attaching them to the drawers. Ensure that everything is sanded smooth before proceeding.

When positioning the drawer pulls, instead of placing them in the center of the drawer, line them up with the top edge. This not only makes installation easier but also gives a visually pleasing result. Simply mark the center on both the drawer and the pull, then align them and glue them into place. No clamping is necessary, as the glue will hold them securely.

Lastly, to achieve a flush look, push the pulls into the front of the cabinet until they are flush with the surface. Add blocks in the back using scrap pieces of lumber, positioning them without adhesive touching the back of the drawer. This will create stability without the need for clamping. Once everything is set, allow the glue to dry completely before moving on to the next steps.

3. “Innovative Drawer Pull Placement: Why I Choose Top Alignment”

When it comes to drawer pulls, I prefer to use solid lumber and create them myself. I usually start with a scrap of lumber and rip it at a thirty-degree angle using my blade. This allows me to attach the pull to the face of the drawer, providing a sturdy grip for easy opening. While I leave the edges that go against the door untouched, I make sure to sand down the part that will be grabbed, ensuring a comfortable and safe user experience.

Before attaching the pulls, I like to sand everything smooth for a polished finish. Additionally, I employ a technique that makes the drawers slide more smoothly. When setting the bottoms of my drawers into rabbet, I make the rabbets slightly deeper than the edges. This reduces the surface area in contact with runners or shelves, making the drawers slide with ease.

Typically, drawer pulls are positioned in the center of a drawer, but I prefer to align them at the top. This allows for easier installation without the need to find the center on each drawer. I simply mark the center on both the drawers and the pulls, align them, and glue them into place. No clamping is necessary, and the glue sets relatively quickly, allowing me to move on with my project without delay. To ensure a flush appearance, I glue blocks of scrap wood behind the pulls, making them flush with the front of the cabinet.

By choosing innovative top alignment for drawer pull placement, I save time and effort while still achieving a pleasing aesthetic. Plus, this method provides a comfortable and secure grip for effortless drawer opening. So why hassle with finding the center when you can easily line up the pulls at the top? Give this alternative placement a try—it’s a simple yet effective solution for your drawer hardware needs.

4. “Troubleshooting and Common Mistakes: Lessons Learned in Drawer Pull Installation

In this section, we will discuss some troubleshooting tips and common mistakes that can occur during drawer pull installation. One common mistake is not properly preparing the drawer pulls before installation. It is important to sand down any sharp edges that may cause discomfort when grabbing the pull. Additionally, it is advisable to sand the pull smooth to give it a polished finish.

Another common mistake is not positioning the drawer pulls correctly. While the traditional approach is to place the pull in the center of the drawer, it can be more convenient to align the pulls with the top of the drawer. This eliminates the need to find the center for each drawer and still provides a visually pleasing result. To achieve this, simply draw a tick mark in the center of each pull and align it with a tick mark in the center of the drawer.

Once the pulls are installed, it is important to ensure they are flush with the front of the cabinet. To achieve this, glue blocks of wood to the back of the cabinet to push the pulls flush. It is crucial to avoid getting glue on the back of the drawer as it may interfere with its functionality. No clamping is necessary for this step, but it is recommended to wait until the glue has fully dried before using the drawers.

By following these troubleshooting tips and being aware of common mistakes, you can ensure a successful and professional-looking drawer pull installation. Remember to properly prepare the pulls, position them accurately, and use glue blocks to achieve a flush finish.

Q&A

Q: What materials does the speaker use to make the drawer pulls?
A: The speaker uses solid lumber, specifically a scrap that was in their lumber cart.

Q: How wide is the scrap of lumber used for the drawer pulls?
A: The speaker is not exactly sure of the width but estimates it to be about an inch and a half.

Q: How does the speaker shape the scrap of lumber for the drawer pulls?
A: The speaker sets the blade of their tool to a thirty-degree angle and rips the lumber at that angle.

Q: Where does the speaker plan to mount the drawer pulls?
A: The drawer pulls will be mounted onto the face of the drawer.

Q: Why does the speaker need to sand down part of the drawer pulls?
A: The speaker wants to sand down certain parts of the drawer pulls to make them less sharp when grabbing them.

Q: How many drawer pulls does the speaker plan to make?
A: The speaker plans to make six drawer pulls.

Q: What does the speaker do before attaching the drawer pulls?
A: Before attaching the drawer pulls, the speaker sands everything really smooth.

Q: What technique does the speaker use when making the bottoms of their drawers?
A: The speaker sets the bottoms of the drawers deeper into the rabbet than the edges, creating less surface area for the drawer to slide on.

Q: Where does the speaker prefer to position the drawer pulls?
A: The speaker prefers to align the drawer pulls with the top of the drawer, rather than placing them in the center.

Q: How does the speaker align the drawer pulls to the top of the drawer?
A: The speaker draws a tick mark in the center of each drawer and a tick mark in the center of each drawer pull to align them.

Q: Does the speaker use clamps when gluing the drawer pulls?
A: The speaker believes clamping is unnecessary for gluing the drawer pulls.

Q: What does the speaker do to ensure the drawer pulls are flush with the front of the cabinet?
A: The speaker pushes the drawer pulls in until they are flush with the front of the cabinet and glues blocks behind them to secure them in place.

Q: Does the speaker use clamps for gluing the blocks?
A: No, the speaker mentions that clamps are not needed for gluing the blocks.

Q: What happens to the speaker’s camera during the video?
A: The speaker accidentally gets glue all over their camera and other materials while working on the project.

Q: According to the speaker, what does he find boring about watching videos?
A: The speaker finds it boring to only see someone’s hands in videos and thinks it would be more interesting to hire a hand model.

Final Notes

In conclusion, this YouTube video provides valuable insights on the process of creating drawer pulls out of solid lumber. The host demonstrates how to rip the lumber at a thirty-degree angle and sand it down for a smoother finish. Additionally, the video highlights the technique of positioning the drawer pulls at the top of the drawer instead of the center, making it easier to align them. Throughout the video, the host emphasizes efficiency and practicality, showcasing their attention to detail and craftsmanship. Overall, this video serves as a helpful guide for anyone looking to enhance the functionality and aesthetics of their drawers.
Clickable here

It’s day 51‍ of the COVID-19​ lockdown and, for many people,⁢ staying at home has been a struggle – but for one unlucky𝅺 couple ‍in 𝅺South Carolina,⁣ it recently took a turn ‍for ​the worse.



In an attempt ⁢to fix a broken air conditioner,⁢ the couple⁢ were forced to make ‌an⁢ emergency call ⁤to an 𝅺HVAC⁤ technician.⁣ But upon the⁤ technician’s arrival, they soon ​realized‍ that the ⁤compressor they had ‍purchased at the local home-improvement⁣ store was too ‍large for ‌their⁤ existing air conditioner.



To their surprise, they learned that there ‍is a size ‍difference between the old and the new𝅺 compressors. The ​old unit was designed 𝅺to ​fit within an enclosed‌ room, ​whereas the new unit was ‌too large ⁤to⁣ do the​ same.‌ Unfortunately, this ⁤created⁢ a𝅺 problem ⁤for ⁤their HVAC​ technician𝅺 as the airflow was⁢ no longer ⁣balanced.

Luckily,⁢ the technician ⁣was able to come up‌ with a ⁣creative solution⁣ – ⁤he cut 𝅺a small‌ hole in the wall​ and installed𝅺 a ⁤wall sleeve in order⁣ to ⁣accommodate ‌the larger compressor. ⁣In ⁢the ⁣end, ​it all worked​ out ‌and𝅺 the ‌couple ‍were‍ able ​to 𝅺have ‌their air​ conditioner up⁤ and ⁢running again.


These 𝅺are strange times, and it’s ​a ‌reminder that things⁣ aren’t always‍ as they seem, ‍even ⁣with HVAC systems. ‌It’s⁢ a good reminder to always get the correct ‍size parts and 𝅺to consult a professional if you are ever ⁣in doubt. A little ⁣extra effort now⁢ can save you 𝅺from a⁣ lot⁤ of ‍headache⁤ later on.


Posted

in

, , , ,

by

Tags: